For more detailed information on any adapter, or for information on jumpers for an adapter that is not listed here, refer to the User Installation Guide that comes with the adapter.
Notes regarding XT/AT bus adapters:
You can ftp the ezsetup-program, copied a long ago from the SMC ftp-site, or look at the other utilities for it.
For a Micro Channel bus board, the RAM base address, I/O base address, boot ROM base address, and interrupt request level are set by the system configuration procedure when the board is installed. Every software driver obtains this information automatically and adjusts its operation accordingly.
"*" DENOTES THE SETTINGS OF JUMPERS INSTALLED AT THE FACTORY.
== EtherCard PLUS ELITE (SMC 8003EP and WD8003EP) ==
JUMPER
BLOCK NAME POSITION FUNCTION
------ ------ ----------- ------------------------------------------
W1 CONFIG SOFT If jumper is installed when power is turned
on, the I/O Base Address, IRQ, and RAM Base
Address are set to the value last stored
with the EZSETUP program. Initially the I/O
Base Address will be 240 with RAM disabled.
280,3,D0000* If jumper is installed when power is turned
on:
-I/O Base Address is set to 280.
-IRQ is set to 3.
-RAM Base Address is set to D0000.
300,5,CA000 If jumper is installed when power is turned
on:
-I/O Base Address is set to 300.
-IRQ is set to 5.
-RAM Base Address is set to CA000.
W2 ROM NONE/SOFT* If jumper is installed when power is turned
ADDR on:
-the ROM Base Address is set to the value
last stored, or is disabled with the EZSETUP
program.
D8000 If jumper is installed when power is turned
on,
-ROM Base Address is set to D8000.
W3 AUI- Ethernet type: use AUI position for thick
BNC Ethernet (external transceiver); use BNC (*)
position for thin Ethernet (BNC connector).
== EtherCard PLUS ELITE16 (SMC 8013EPC and WD8013EP) ==
JUMPER
BLOCK NAME POSITION FUNCTION
------ ------ ----------- ------------------------------------------
W1 CONFIG SOFT If jumper is installed when power is turned
on, the I/O Base Address, IRQ, and RAM Base
Address are set to the value last stored
with the EZSETUP program. Initially the I/O
Base Address will be 240 with RAM disabled.
280,3,D0000* If jumper is installed when power is turned
on:
-I/O Base Address is set to 280.
-IRQ is set to 3.
-RAM Base Address is set to D0000.
300,10,CC000 If jumper is installed when power is turned
on:
-I/O Base Address is set to 300.
-IRQ is set to 10.
-RAM Base Address is set to CC000.
W2 ROM SOFT* If jumper is installed when power is turned
ADDR on:
-the ROM Base Address is set to the value
last stored, or is disabled with the EZSETUP
program.
D8000 If jumper is installed when power is turned
on,
-ROM Base Address is set to D8000.
W3 AUI- Ethernet type: use AUI position for thick
BNC Ethernet (external transceiver); use BNC (*)
position for thin Ethernet (BNC connector).
NOTE! The SMC 8013EPC does not contain
a W3 jumper, cable type is configured
through EZSETUP.
== EtherCard PLUS ELITE16C (SMC 8013EWC and WD8013EW) ==
JUMPER
BLOCK NAME POSITION FUNCTION
------ ------ ----------- ------------------------------------------
W1 CONFIG SOFT If jumper is installed when power is turned
on, the I/O Base Address, IRQ, and RAM Base
Address are set to the value last stored
with the EZSETUP program. Initially the I/O
Base Address will be 240 with RAM disabled.
280,3,D0000* If jumper is installed when power is turned
on:
-I/O Base Address is set to 280.
-IRQ is set to 3.
-RAM Base Address is set to D0000.
300,10,CC000 If jumper is installed when power is turned
on:
-I/O Base Address is set to 300.
-IRQ is set to 10.
-RAM Base Address is set to CC000.
W2 ROM SOFT* If jumper is installed when power is turned
ADDR on:
-the ROM Base Address is set to the value
last stored, or is disabled with the EZSETUP
program.
D8000 If jumper is installed when power is turned
on,
-ROM Base Address is set to D8000.
W3 AUI- Ethernet type: use AUI position for thick
BNC Ethernet (external transceiver); use BNC (*)
position for thin Ethernet (BNC connector).
NOTE! The SMC 8013EWC does not contain
a W3 jumper, cable type is configured
through EZSETUP.
== EtherCard PLUS ELITE16T (SMC 8013WC and WD8013W) ==
JUMPER
BLOCK NAME POSITION FUNCTION
------ ------ ----------- ------------------------------------------
W1 CONFIG SOFT If jumper is installed when power is turned
on, the I/O Base Address, IRQ, and RAM Base
Address are set to the value last stored
with the EZSETUP program. Initially the I/O
Base Address will be 240 with RAM disabled.
280,3,D0000* If jumper is installed when power is turned
on:
-I/O Base Address is set to 280.
-IRQ is set to 3.
-RAM Base Address is set to D0000.
300,10,CC000 If jumper is installed when power is turned
on:
-I/O Base Address is set to 300.
-IRQ is set to 10.
-RAM Base Address is set to CC000.
W2 ROM SOFT* If jumper is installed when power is turned
ADDR on:
-the ROM Base Address is set to the value
last stored, or is disabled with the EZSETUP
program.
D8000 If jumper is installed when power is turned
on,
-ROM Base Address is set to D8000.
== EtherCard PLUS with Boot ROM Socket (WD8003EB) ==
JUMPER
BLOCK NAME FUNCTION
------ ---- ---------------------------------------------
W1 INIT If jumper is installed when power is turned on,
280 I/O Base Address is temporarily set to 280.
Setup Program must then be run to store new I/O
Base Address, and jumper must be removed (*).
W3 AUI- Ethernet type: use AUI position for thick
BNC Ethernet (external transceiver); use BNC (*)
position for thin Ethernet (BNC connector).
W9 ROM Size of optional ROM installed (2 jumpers).
Size LEFT JUMPER RIGHT JUMPER
POSITION POSITION
16 Kbytes(*) Top Top
32 Kbytes Bottom Top
64 Kbytes Bottom Bottom
Jumpers are ignored if no ROM is installed
and ROM is disabled through EZSETUP.
== EtherCard PLUS16 16-Bit Ethernet Adapter (WD8013EBT) ==
JUMPER
BLOCK NAME FUNCTION
------ -------- --------------------------------------------
W0 Wait Reduces the required wait states for an 8-
States bit memory access from four to two.
8-Bit
Access
W0 Wait Reduces the required wait states for a 16-
State bit memory access from one to zero.
16-Bit
Access Install both the 8-and 16-bit jumpers to
enhance performance on systems with I/O
bus speeds of 8MHz or less. Factory setting
is both jumpers removed, which ensures
correct operation in faster bus systems.
The jumpers are ignored in XT bus systems.
W1 I/O Base Selects the hex I/O Base Address. Options
Address are 200, 220, 240, 260, 280(*), 2A0,
2C0, 300, 340, and 380
W2 IRQ Selects the interrupt request (IRQ) level
Level to be used by the adapter. IRQ10, 11 and
15 are not available in 8-bit bus systems
such as the IBM PC and PC XT. IRQ2/9
position selects IRQ2 for PC and XT type
systems (8-bit bus), and IRQ9 for AT type
systems (16-bit bus). Only one jumper
may be installed at a time.
IRQ options are: 2, 3(*), 4, 5, 7,
9, 10, 11, 15
W3 AUI- Ethernet type: Use AUI position for thick
BNC Ethernet (external transceiver): Use BNC(*)
position for thin Ethernet (BNC connector).
W6 ROM Selects ROM memory space, if a ROM is
Memory installed. Options: NONE(*), 16K, 32K,
Space and 64K
W9 ROM Size of optional ROM installed (2 jumpers).
Size Jumpers are ignored when W6 is set to NONE.
ROM SIZE TOP JUMPER BOTTOM JUMPER
POSITION POSITION
16 Kbytes(*) Left Left
32 Kbytes Left Right
64 Kbytes Right Right
W15 ROM Establishes the base address for the ROM
Base device (Up to 3 jumpers). Jumpers are
Address ignored when W6 is set to NONE.
SELECTED JUMPERS INSTALLED AT:
ADDRESS C4000 C8000 D0000
C0000
C4000 X
C8000 X
D0000 X
CC000 X X
D4000 X X
D8000(*) X X
DC000 X X X
NOTE! X - Represents an installed jumper.
== EtherCard PLUS (WD8003E) ==
And
== EtherCard PLUS With Boot ROM Socket (WD8003EBT) ==
JUMPER CLOSED FUNCTION SELECTED
BLOCK PIN #'S NAME WHEN JUMPER IS INSTALLED
------ -------- ---- ----------------------------
W1 1-2 Zero Select zero wait states for optimized
Wait operation in a 6MHz AT. (Factory
setting is jumper removed, which
ensures correct operation in faster
AT bus systems.) This jumper is
ignored in XT bus systems.
W1 I/O Base Selects the I/O Base Address
Address
3-4, 5-6, 7-8, 9-10 = 200
5-6, 7-8, 9-10 = 220
3-4, 7-8, 9-10 = 240
7-8, 9-10 = 260
3-4*,5-6*,9-10* = 280 -- the factory setting
5-6, 9-10 = 2A0
3-4, 9-10 = 2C0
9-10 = 2E0
3-4, 5-6, 7-8 = 300
5-6, 7-8 = 320
3-4, 7-8 = 340
7-8 = 360
3-4, 5-6 = 380
5-6 = 3A0
3-4 = 3C0
NONE = 3E0
W2 1-2 IRQ7 Interrupt request level.
3-4 IRQ6 Only one jumper may be installed at a
5-6 IRQ5 time.
7-8 IRQ4
9-10* IRQ3 (Factory setting is IRQ3)
11-12 IRQ2
W3 1-2* AUI- Ethernet type: pins all jumpered to
3-4* BNC use J1 BNC connector for thin Ethernet
5-6* cable (* - the factory setting).
7-8* Jumpers all removed to use J2 AUI
9-10* connector (thick Ethernet cable).
11-12*
W4 1-2 Ethernet Jumper removed for thin Ethernet and
Version IEEE 802.3/Version 2 thick Ethernet
(the factory setting); jumper in-
stalled for thick Ethernet Version 1.
W5 1-2* Segment Selects thin Ethernet segment length:
Length jumpered for IEEE 802.3 standard 185m
length (*-the factory setting); jumper
removed for 300m extended length.
== Additional Jumpers On ==
== EtherCard PLUS With ROM Socket Only (WD8003EBT) ==
JUMPER CLOSED FUNCTION SELECTED WHEN
BLOCK PIN #'S NAME INDICATED JUMPERS ARE INSTALLED
------ ------- ---- ------------------------------------
W6 NONE ROM C0000 (16K, 32K, 64K ROMs)
1-2 Base C4000 (16K ROMs)
3-4 Address C8000 (16K, 32K ROMs)
1-2, 3-4 CC000 (16K ROMs)
5-6 D0000 (16K, 32K, 64K ROMs)
1-2, 5-6 D4000 (16K ROMs)
3-4*, 5-6* D8000 (16K, 32K ROMs)--factory setting
1-2, 3-4, 5-6 DC000 (16K ROMs)
(NOTE: Do not use addresses C0000
or C4000 for Boot ROMs)
W6 7-8*,9-10* ROM ROM Disabled -- the factory setting
W9 3-4* Size "
W10 3-4* "
W6 NONE ROM 16 Kbytes ROM
W9 3-4 Size "
W10 3-4 "
W6 7-8 ROM 32 Kbytes ROM
W9 3-4 Size "
W10 1-2 "
W6 9-10 ROM 64 Kbytes ROM
W9 1-2 Size "
W10 1-2 "
W7 3-4* RAM 8 Kbytes RAM -- the factory setting
W8 3-4* Buffer "
W11 2-3* Size "
W7 1-2 RAM 32 Kbytes RAM
W8 1-2 Buffer "
W11 1-2 Size " (NOTE: valid 32 Kbyte RAM
base addresses are C0000, C8000,
D0000 and D8000.)
== EtherCard PLUS TP For Unshielded Twisted Pair Wiring,
LattisNet Compatible (WD8003WT) ==
JUMPER CLOSED FUNCTION SELECTED
BLOCK PIN #'S NAME WHEN JUMPERS ARE INSTALLED
------ -------- ---- -------------------------------------
W1 1-2 Zero Select zero wait states for optimized
Wait operation in a 6MHz AT. (Factory
State setting is jumper removed, which
ensures correct operation in faster
AT bus systems.) This jumper is
ignored in XT bus systems.
W1 I/O Base Selects the I/O Base Address
Address (Up to 3 jumpers)
3-4, 5-6, 7-8, 9-10 = 200
5-6, 7-8, 9-10 = 220
3-4, 7-8, 9-10 = 240
7-8, 9-10 = 260
3-4*,5-6*,9-10* = 280 -- the factory setting
5-6, 9-10 = 2A0
3-4, 9-10 = 2C0
9-10 = 2E0
3-4, 5-6, 7-8 = 300
5-6, 7-8 = 320
3-4, 7-8 = 340
7-8 = 360
3-4, 5-6 = 380
5-6 = 3A0
3-4 = 3C0
NONE = 3E0
W2 1-2 IRQ7 Selects the Interrupt request level.
3-4 IRQ6 Only one jumper may be installed at a
5-6 IRQ5 time.
7-8 IRQ4
9-10* IRQ3 -- the factory setting
11-12 IRQ2
W3 1-2* RJ-45 Ethernet type: pins all jumpered to
3-4* -AUI use RJ-45 twisted pair wiring connec-
5-6* tor (*-the factory setting). Jumpers
7-8* all removed to use AUI connector.
9-10*
11-12*
W6 ROM Base Selects the ROM base address
Address (Up to 3 jumpers)
NONE C0000 (16K, 32K, 64K ROMs)
1-2 C4000 (16K ROMs)
3-4 C8000 (16K, 32K ROMs)
1-2, 3-4 CC000 (16K ROMs)
5-6 D0000 (16K, 32K, 64K ROMs)
1-2, 5-6 D4000 (16K ROMs)
3-4*, 5-6* D8000 (16K, 32K ROMs)--factory setting
1-2, 3-4, 5-6 DC000 (16K ROMs)
(NOTE: Do not use addresses C0000
or C4000 for Boot ROMs)
W6 7-8*,9-10* ROM ROM Disabled -- the factory setting
W9 2-3* Size "
W10 2-3* "
W6 NONE ROM 16 Kbytes ROM
W9 2-3 Size "
W10 2-3 "
W6 7-8 ROM 32 Kbytes ROM
W9 2-3 Size "
W10 1-2 "
W6 9-10 ROM 64 Kbytes ROM
W9 1-2 Size "
W10 1-2 "
W7 2-3* RAM 8 Kbytes RAM -- the factory setting
W8 2-3* Buffer "
W11 2-3* Size "
W7 1-2 RAM 32 Kbytes RAM
W8 1-2 Buffer "
W11 1-2 Size " (NOTE: valid 32 Kbyte RAM
base addresses are C0000, C8000, D0000
and D8000.)
== EtherCard PLUS10T for Unshielded Twisted Pair Wiring - 10BaseT
Draft Standard Compatible ( WD8003W ) ==
JUMPER
BLOCK NAME FUNCTION
------ ---- ---------------------------------------------
W1 INIT If jumper is installed when power is turned on,
280 I/O Base Address is temporarily set to 280.
Setup Program must then be run to store new I/O
Base Address, and jumper must be removed (*).
W9 ROM Size of optional ROM installed (2 jumpers).
Size LEFT JUMPER RIGHT JUMPER
POSITION POSITION
16 Kbytes(*) Top Top
32 Kbytes Bottom Top
64 Kbytes Bottom Bottom
Jumpers are ignored if no ROM is installed.
W20 Auto In the ON position (*), the adapter automati-
Polarity cally corrects for incorrect polarity on the
Correction receive twisted pair. If W20 is installed in
the OFF position, the receive twisted pair
polarity must be correct on the RJ-45 port
according to the 10BaseT standard.
W21 Link The 10BaseT link integrity test between the
Integrity adapter and a 10BaseT concentrator is per-
formed with the jumper removed (*). The
link integrity test is not performed if the
jumper is installed.
== EtherCard PLUS10T for Unshielded Twisted Pair Wiring - 10BaseT
Draft Standard Compatible ( SMC 8003WC ) ==
JUMPER
BLOCK NAME POSITION FUNCTION
------ ------ ----------- ------------------------------------------
W1 CONFIG SOFT If jumper is installed when power is turned
on, the I/O Base Address, IRQ, and RAM Base
Address are set to the value last stored
with the EZSETUP program. Initially the I/O
Base Address will be 240 with RAM disabled.
280,3,D0000* If jumper is installed when power is turned
on:
-I/O Base Address is set to 280.
-IRQ is set to 3.
-RAM Base Address is set to D0000.
300,5,CA000 If jumper is installed when power is turned
on:
-I/O Base Address is set to 300.
-IRQ is set to 5.
-RAM Base Address is set to CA000.
W2 ROM SOFT* If jumper is installed when power is turned
ADDR on:
-the ROM Base Address is set to the value
last stored, or is disabled with the EZSETUP
program.
D8000 If jumper is installed when power is turned
on,
-ROM Base Address is set to D8000.
== EtherCard PLUS/A For Micro Channel (WD8003ET/A) ==
JUMPER CLOSED FUNCTION SELECTED WHEN
BLOCK PIN #'S NAME INDICATED JUMPERS ARE INSTALLED
------ -------- ---- ------------------------------------
W3 1-2* AUI- Ethernet type: pins all jumpered to
3-4* BNC use J1 BNC connector for thin Ethernet
5-6* cable (*-the factory setting).
7-8* Jumpers all removed to use J2 AUI
9-10* connector (thick Ethernet cable).
11-12*
W9 2-3* ROM 16 Kbytes ROM -- the factory setting
W10 NONE* Size "
W9 1-2 ROM 32 Kbytes ROM
W10 1-2 Size "
W9 2-3 ROM 64 Kbytes ROM
W10 1-2 Size "
== EtherCard PLUS/A for Micro Channel (WD8003E/A) ==
JUMPER
BLOCK NAME FUNCTION
------ ---- ---------------------------------------------
W3 AUI- Ethernet type (2 jumpers): Use AUI position
BNC for both jumpers for thick Ethernet (external
transceiver); Use BNC (*) position for both
jumpers for thin Ethernet (BNC connector).
W9,W10 ROM Size of optional ROM installed (2 jumpers).
Size
W10 W9
16 Kbytes (*) Top Top
32 Kbytes Bottom Top
64 Kbytes Bottom Bottom
Jumpers are ignored if no ROM is installed
and ROM is disabled via the configuration diskette.
== EtherCard PLUS10T/A for Micro Channel (WD8003W/A) ==
JUMPER
BLOCK NAME FUNCTION
------ ---- ---------------------------------------------
W9,W10 ROM Size of optional ROM installed (2 jumpers).
Size
W10 W9
16 Kbytes (*) Top Top
32 Kbytes Bottom Top
64 Kbytes Bottom Bottom
Jumpers are ignored if no ROM is installed
and ROM is disabled via the configuration diskette.
W20 Auto In the ON position (*), the adapter automati-
Polarity cally corrects for incorrect polarity on the
Correction receive twisted pair. If W20 is installed in
the OFF position, the receive twisted pair
polarity must be correct on the RJ-45 port
according to the 10BaseT standard.
W21 Link The 10BaseT link integrity test between the
Integrity adapter and a 10BaseT concentrator is per-
formed with the jumper removed (*). The
link integrity test is not performed if the
jumper is installed.
== StarCard PLUS/A For Micro Channel (WD8003ST/A) ==
JUMPER CLOSED FUNCTION SELECTED WHEN
BLOCK PIN #'S NAME INDICATED JUMPERS ARE INSTALLED
------ -------- ---- ------------------------------------
W9 2-3* ROM 16 Kbytes ROM--the factory setting
W10 NONE* Size "
W9 2-3 ROM 32 Kbytes ROM
W10 1-2 Size "
W9 1-2 ROM 64 Kbytes ROM
W10 1-2 Size "
== StarCard PLUS (WD8003S) ==
And
== StarLink PLUS (WD8003SH) ==
JUMPER CLOSED FUNCTION SELECTED
BLOCK PIN #'S NAME WHEN JUMPER IS INSTALLED
------ -------- ---- ----------------------------
W2 1-2 Zero Select zero wait states for optimized
Wait operation in a 6MHz AT. (Factory
setting is jumper removed, which
ensures correct operation in faster
AT bus systems.) This jumper is
ignored in XT bus systems.
W2 I/O Base Selects the I/O Base Address
Address (Up to 3 jumpers)
3-4*,5-6*,9-10* 280 -- the factory setting
5-6, 9-10 2A0
3-4, 9-10 2C0
9-10 2E0
3-4, 5-6, 7-8 300
5-6, 7-8 320
3-4, 7-8 340
W1 1-2 IRQ7 Interrupt request level.
3-4 IRQ6 Only one jumper may be installed at a
5-6 IRQ5 time.
7-8 IRQ4
9-10* IRQ3 -- the factory setting
11-12 IRQ2
W3 1-2* StarCard PLUS (WD8003S):
Jumper must be installed
1-2 StarLink PLUS (WD8003SH):
Jumper must be removed
(for compatibility with 802.3 1BASE5
StarLAN standard.)
== Additional Jumpers On ==
== StarLink PLUS Only (WD8003SH) ==
JUMPER CLOSED FUNCTION SELECTED WHEN
BLOCK PIN #'S NAME INDICATED JUMPERS ARE INSTALLED
------ -------- --------- -----------------------------------
W4 11-12 ROM Enabled when jumper installed;
Enable disabled (the factory setting) when
jumper removed
W4 ROM Base Selects the ROM Base Address
Address (Up to 3 jumpers)
3-4*,7-8*,9-10* C8000 (16K, 32K ROMs)--factory setting
7-8, 9-10 CC000 (16K ROMs)
3-4, 5-6,9-10 D0000 (16K, 32K, 64K ROMs)
5-6, 9-10 D4000 (16K ROMs)
3-4, 9-10 D8000 (16K, 32K ROMs)
W5 1-3*, 2-4* ROM 16 Kbytes ROM -- the factory setting
W6 1-3*, 2-4* Size "
W5 1-3, 4-6 ROM 32 Kbytes ROM
W6 1-3, 4-6 Size "
W5 3-5, 4-6 ROM 64 Kbytes ROM
W6 3-5, 4-6 Size "
[an error occurred while processing the directive]